H

How to install metal edging on your retro laminate countertops

easy buttonSeveral readers have asked me how to install the stainless steel countertop edging from New York Metals. In this post, I’ll take you step-by-step through the process that we used to install the metal edging in my kitchen.

I had my countertops laminated by an outfit recommended by by contractor. They made all the countertops and backsplashes separately, ahead of time, and then, when they came to install them in my kitchen, they put everything together.

To review…The edging is comprised of three different pieces.

This is the little cove molding piece you use to mask where the countertop attaches to the backsplash. The part that “shows” is the 5/16″ part. You shove the 15/16″ part back down behind the main countertop:

stainless steel counter edging cove molding

This next piece, the 1-5/8″ snap-on molding, goes along the edge of the main countertop.

steel countertop edging retro style

The question I have been receiving is, how to you handle the corners.

Answers: On the OUTSIDE corners, you snip the the metal lip that sit on top of the countertop and along the underside and miter it; the fat 1.5″ part of the metal bends easily to make the turn:

how to install metal counter edgeOn INSIDE corners, you cut the whole piece, also making miters on the lip that sit on the counter and underside.

metal countertop bandingNow, somewhere in my stash I saw 50s DIY instructions on how to then weld… spotweld?… sauter? the mitered edges for a clean finish.  Who knows which word? Lord knows which of 400 magazines this little article in. But I’ll keep an eye out. In any case, we did NOT weld anything and honestly, it’s fine. It kind of looks worse in the photo above than it is in real life. The miters are just real tight. Hey, if anyone is out on retro recon, with a camera and sees welded corners – grab the shot and send it in.

stainless steel countertop edging for the backsplash piece

Finally – the 1″ backsplash…corners, miters…are handled the same way. In spots where the backsplash edges are visible vertically as in the photo below – back by the wallpaper – we made the bend then just secured them with a bead of glue. No screws were used.

metal edging for a backsplash

bending metal countertop edging

Contractor Kevin, along with the countertop guys, were quite trepidatious about the whole thing coming in. This was the first time any of them had done this, their dads had done it 50 years ago! It really was a breeze, though. And as with the rest of my darling beloved kitchen – all the naysayers who thought I was nutso – were totally won over in the end and LOVED IT!

metal edging kitchen counter tops

Above – Reader Amy asked you to “end” the countertop against a well. Here’s Option #1 – you run the backsplash all the way around.

metal counter band

Above – Option #1 e.g., where the countertop ends against a fridge, we wrapped the countertop in 1-5/8″ molding there – no backsplash.

Hope this all makes sense. 

Note that metal countertop banding is available from a number of companies in a variety of metals. Some are u-shaped, like the kind I used, while others are t-shaped and require routing. Others also may have cute banding. And, there’s shiny and matte finish to decide on. Lots of choices!

    1. Pam Kueber says:

      Just under 3″ including the stainless steel molding. Note, I didn’t do it to any ‘standards’ – I sized them so that they hit just below the kitchen window, which sits quite low/close to the countertop.

  1. Joel says:

    According to the New York Metals website, the 5/16″ cove moulding (SS799) is no longer in stock. Any alternative suggestions?

  2. Nicholas Balandiat says:

    Did you have to order the metal edge banding from their website or can you find this stuff locally.

    I have basically the same pattern but in white with the triangles. I want to redo the kitchen and I will need new countertops but more of them. I always loved the metal edge banding I have now

    1. Pam Kueber says:

      I think you may be able to find it locally if you live in certain mid mod mad cities, like Los Angeles. Other than that, I do not know…

  3. Lisa Gendy says:

    Hi I am looking to replace the laminate on my mother in laws counters which also have this metal trim. Is it possible to remove the trim and reuse it? The stainless trim is in beautiful condition.
    Thanks, Lisa

  4. Brendan says:

    Did you use a clear silicon caulk around all the metal edges to seal it so liquid and crumbs can’t make their way between the metal and the laminate?

    1. Pam Kueber says:

      I don’t think my installer did this. I suggest you talk to the folks at New York Metals regarding this question… historically, they have been very responsive…

    1. Pam Kueber says:

      Hi Nick, for installation instructions one needs to check with the manufacturer. My edging — which came from New York Metals — was installed by professionals, I am not sure what they did.

Leave a Reply

Commenting: Information

All comments are moderated, generally within 24 hours. By using this website you are agreeing to the site's >> Terms of Service, << which include commenting policies, and our >> Privacy Notice. << Before participating, read them in full.

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.